 The
HD Strip Heater's highly compacted refractory material quickly conducts
heat from the resistance wire to the sheath resulting in low internal
temperatures and long heater life in the most demanding applications.
Precise placement of the resistance wire provides uniform sheath
temperature across the width and along the entire heated length.
Terminal designs allow easy installation wiring. 3/8" thickness
creates a rigid sheath for secure clamping ability. The HD Strip
Heater is ideally suited for many industrial and commercial applications.
|
|
 |
|
Highly
compressed refractory material for outstanding performance in
surface heating or convection air heating applications
 |
|
 |
|
 |
|
|
|
|
|
|
| FINNED HD STRIP HEATERS | |
|
|
Finned
HD Strip Heaters feature the same highly compressed, rugged design
as HD Strip Heaters with the addition of 1-3/8" X 2"
fins. Fins increase the heat transfer surface area to allow higher
wattages than standard HD Strip Heaters. Rust resisting iron sheath
items are standard with aluminized steel fins. Stainless steel
sheath items are standard with stainless steel fins. Convection
heating or processes requiring a high velocity air stream are
among the many possible applications for Finned HD Strip Heaters.
| MIGHTY-TUFF STRIP HEATERS | |
| The Mighty-Tuff Strip Heater provides high temperatures, extreme watt densities and quick responses in applications where previously, any other type of strip heater could not be considered. Heat is transferred rapidly from the resistance element to the sheath for lower internal temperatures and long life. The thin but rugged design can produce high sheath temperatures at high watt densities. The Mighty-Tuff is versatile with the availability of widths to 6" and lengths to 42". In the most difficult application or in normal use, the Mighty-Tuff will significantly improve strip heater performance. Careful consideration in clamping strip heaters to the surface will improve heat transfer and extend heater length of service. |
 |
 |
|
2-1/2"
wide Mighty-Tuff with SG terminals. SG terminals are perpendicular
to the length and have 10-24 threads. Available on 2" and wider.
|
2-1/2"
wide Mighty-Tuff with SG terminals and 3/8" diameter mounting
holes.
|
 |
 |
|
7/8"
wide Mighty-Tuff Strip Heater with SE terminals. 10-24 threads
with a terminal at each end is the standard design.
|
7/8"
wide Mighty-Tuff with SE terminals and 3/8" diameter mounting
holes.
|
 |
 |
|
Mighty-Tuff
Strip heaters can be supplied with any lead configuration as shown
on Mighty-Tuff Bank Heater section, such as Type F, C, A, R or
P. The illustration is with Type C Armor Cable protected leads.
|
|
|
|
|
| MICA STRIP HEATERS | |
|
Versatile, efficient and economical, the Mica Strip Heater is of the same construction as the Mica Band Heater in flat design. Because of the range of dimensions and configuration possible, these units furnish even heat distribution for use in hot plates, sealing equipment, hot stamping, dies and molds and hundreds of other surface heating applications. (PDF file - 4k) |
|
 |
 |
|
TYPE
L1 - Widths over 3/4". 12" lead wires standard.
|
TYPE
L2 - Widths over 1". 12" lead wires standard.
|
 |
 |
|
TYPE
T1 - Widths over 1". Requires 1" cold section each
end.
|
TYPE
T2 - Widths over 1-1/2". Requires 1-1/2" cold section
at terminal end.
|
 |
 |
|
TYPE
T3 - Widths 1-3/4" cold section at terminal end.
|
TYPE
B2 - (Tapped Terminals)
|
| (T1, T2 & T3 terminals have 10-24 thread and require 15/16" clearance from surface being heated. B1, B2 & B3 require 1/2" clearance.) | |
 |
 |
|
Full
case - For use where surface contact on both sides
of heater is necessary.
|
Mica Strip Heaters are also available with lead modifications fig. 3,5,6 & 16(shown) and plug configurations as shown in the Mica Band Heater section. |
| Watt densities to 35wi2. Standard thickness is 5/32". When ordering, specify: length and width, type of termination, wattage and voltage (resistance tolerance +10; -5%) and special features. | |
|
|
||||
|
Important Notice: By purchasing products from this Site, you acknowledge and agree that you have read and accept the Terms and Conditions of this online store. For more information email us at: info@iprocessmart.com |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
