MIGHTY-TUFF® BAND HEATERS Rugged construction along with high temperature and high watt density capabilities allow the Mighty-Tuff Band Heater to surpass all other band heaters in providing the ever increasing temperatures required for processing today's high tech materials. The advanced design and thin profile allow the quick transfer of heat from the element to the sheath for efficient operation to 1400 F sheath temperature. Watt densities as high as 200 watts per square inch on small diameters and 100 watts per square inch on larger diameters are possible. The Mighty-Tuff can stand up to shock, vibration and many contaminants long after standard band heaters have failed. In normal use, or in the most difficult application, the Mighty-Tuff will improve machine productivity by improving band heater performance. Stainless Steel Sheath to resist oxidation Capable of operating up to 1400 F Sheath Temperature Highest possible application temperatures Over 200 watts per square inch capacity Thin profile (3/16") for rapid response Mighty-Tuff Catalog Sheet MIGHTY-TUFF TERMINATIONS Type F - High Temperature Leads 12" long 850°F/450°C insulated lead wires are standard. Specify longer length. Also available with full length fiberglass sleeveing. Type C - Armor Cable Leads Armor cable is the best protection for abrasion. 12" cable and 14" overall leads are standard. Type A / Type R / Type P Metal Braided Leads Type H - Hole or Cut-out Mighty-Tuff Band Heaters can be manufactured with thermocouple holes, slots or notches. Consult Ogden. Mighty-Tuff with Insulated Shroud Mighty-Tuff Band Heaters are available with an insulated shroud. Similar in effect to Ceramic Band Heaters, heat losses to the environment are greatly reduced. The thin profile and compressed design, the Mighty-Tuff transfers heat to the cylinder rapidly. Post Terminals Type SG - Terminals at gap. Minimum width­2" Type SH - Terminals 180° from gap. Also available with 2" H x 1-1/2" W x 2"L terminal box. Type E - One Piece Expandable (Shown with Type SG terminals) Specify termination, terminal location and other options. Type T - Two Piece Construction (Shown with Type A leads and optional spring loaded screws) Specify termination, terminal location and other options. European Style High Temperature Plugs Type 110: 2-1/2" H x 1-3/16" L x 2-1/8" W Type 115: Dimensions - 1-1/4" H x 3-1/4"L x 1-11/16"W Fig. GQ8: Receptacle PC4396-3 Other plugs attached to leads are available. Type L - Mounting Flange Standard on all Mighty-Tuff Band Heaters. Supplied with Socket Head Cap Screw. Type S MT Band Heaters are available with 5/8" wide straps. Some dimensional restrictions may apply based on lead type, position and width. Maximum Watt Density for 1-1/2" Wide Mighty-Tuff Band Heaters: Cycled moderately. Tightly clamped on a smooth surface. For units over 2" in width multiply watt density by 0.8. Where insulating blankets are used, multiply watt density by 0.7. See the technical section for estimating watt density.     Type BL Low Profile Barrel Nut Assembly Welded to Sheath. Type BN Standard Profile Barrel Nut Assembly Welded to Sheath. Type BR Quick Release Assembly with Spring Loaded Screw Welded to Sheath. Type BT Quick Release Barrel Nut Assembly Welded to Sheath. Type BW 1-1/4" Wide Barrel Nut Assembly Welded to Sheath.     Ordering Information: Catalog number if available Inside diameter and width Wattage and voltage If one piece expandable (Type E) or two piece construction (Type T), specify total wattage and operating voltage Type of termination and length of leads, if applicable Type of Mounting Submit sketch or drawing, if necessary

Band - Mighty Tuff