Store Front Account Search Basket Contents Checkout
Sign In
Order History


Manufacturers
Environmental
Temperature
   Heaters
     Band Heaters
       Band - Mica
       Band - Ceramic
       Band - Mighty Tuff
       Band - Aluma Flex
     Insertion Heaters
     Flameless Air Heaters
     Process Air Heaters
     Immersion Heaters
     Flexible Silicone Heaters
     Strip Heaters
     Insulated Blanket Heaters
     Insulated Drum Heaters
     Spray Foam Warming
   Temp. Sensors
   Portable Instruments
   Controls & Interfaces
   Cooling
   Controls & Interfaces
Level
Pressure
Flow
Sensors & Transmitters

 

 

 

 

sales@iprocessmart.com
Tel: 1-925-706-7433


Ogden Chromalox Mica Band Heaters
Ogden / Chromalox

MICA BAND HEATERS

Ogden Mica Band Heaters A mica core produces a thin, efficient heater. Heat from the precisely wound Nichrome element is quickly transferred to the working surface for fast heat-up and response. Mica provides excellent dielectric strength and heat transfer capability for long heater life. The mica core is encased in a continuous corrosion resistant sheath and formed. All full mica band heaters are designed with closed ends to protect against contamination. Maximum sheath temperature is 800° F.

Ordering Information:

Additional Variations

  • Catalog number if available
  • Inside diameter x width
  • Watts and Volts
  • If 2 piece, watts and volts each half
  • Termination Type
  • Modifications or options
  • Sketch or drawing if necessary
  • Three terminal or lead, dual voltage, three phase or ground
  • Appliance pin terminals
  • Full length fiberglass sleeving
  • Rectangular or segment band heaters­provide drawing
  • Outside diameter design for internally heating cylinder
  • Stainless steel or Monel sheath for use in corrosive atmosphere
  • Metric Sizes
BAND HEATER TERMINATIONS   MOUNTING CONFIGURATIONS
Leads Wires:
Fig.1 Fig. 1: Usual design for nozzle heating applications. 12" leads are standard.
Fig.3 Fig. 3: Single conductor metal braid over lead wire. Offers most practical solution to abrasion problem. 12" braid with 14" overall length leads are standard.
Fig.4 Fig. 4: Standard lead wires exiting 180° from gap.
Fig.5 Fig. 5: Leads exit at right angle to sheath 5/8" from gap. 12" lead wire in 3" long sleeving is standard. Specify alternate position.
Fig.6 Fig. 6: Flexible armor cable is the best solution to lead abrasion problems. 12" armor with 14" overall length leads are standard. Specify alternate position.
Fig.7 Fig. 7: Double conductor metal braid exiting from edge 180° from gap.
Fig.16 Fig. 16: Double conductor metal braid over lead wires at same position as Fig. 5. 12" braid with 14" overall length leads are standard. Specify alternate position.
TERMINAL PROTECTION
Terminal Box Cover: 2" H x1-1/2" W x 2" L. Also available in a 2-1/4" H x 2-1/16" W x 4-1/2" L terminal box for larger clearance to terminals.
Ceramic Terminal Cover: 7/8" high x 3/4" O.D. for 10-24 thread. (PC4379-2; PC4380-1)
   
   
Screw Terminals:

Fig. T1

Fig. T1: Standard position under 2-1/2" wide.

Fig. T2

Fig. T2: Standard position over 2-1/2"wide.

Fig. T3

Fig. T3: Standard with terminal box.

Fig. B1

Fig. B1 (shown) B2, B3: 10-32 thread requires 1/2" clearance from cylinder.
  Special Features:
Fig.12 Fig. 12: Hinged Half-Band- convenient where two piece heaters are required. Shown with Fig. 8 mounting flange and T2 screw terminals. Available with any termination or mounting arrangement.
Fig. 14 Fig. 14: Half Band-eases installation in difficult situations. Shown with T1 Terminals and Fig. 10 by-pass straps. Available with any termination or mounting arrangement
Fig.15 Fig. 15: Probe holes and cut-outs-specify location in degrees from center of gap and size or provide drawing. Often a larger gap (standard gap is 1/4" - 1") will serve the same purpose.
Fig.17 Fig. 17: Splitcase-Allows heater to be opened one time for mounting. Available with any termination or mounting arrangement.
Fig.9 Fig. 9 Strap-made from a low expansion alloy to tighten around the whole circumference of the heater.
Low Profile: H = 1/4", 1/2" wide (Supplied on 3" I.D. and less). Standard Profile: H = 3/8", 5/8" wide (supplied on 3-1/8" I.D. and larger). Also available with hose clamp or punch lock strap.
Fig.8 Fig. 8 Mounting Flange-a secondary means for mounting where a built-in method is preferred.
Fig.10 Fig. 10 By-Pass Strap-Supplied on less than 2" wide with terminals or Figures 5, 6 or 16.
Fig.11 Fig. 11 Wedge Mount-for applications where an extremely low profile is required or where access is limited. Available with Figures 1, 3, 4, 5, 7 and 16 leads.
Fig.18 Fig. 18: Low Profile Barrel Nut Assembly Welded to Sheath
Fig.19 Fig. 19: Standard Profile Barrel Nut Assembly Welded to Sheath
Fig.20 Fig. 20: 1-1/4" Wide Barrel Assembly Welded to Sheath
Fig.21 Fig. 21 Quick Release Assembly with Spring Loaded Screw ­ Assembly Welded to Sheath
EURO STYLE HIGH TEMPERATURE PLUG
Euro Plugs Fig. 110: Dim: 3-1/2" H x 1-5/16" L x 2-15/16"
Fig. 115: Dim: 1-3/8" H x 3-7/16" L x 1-7/8" W
Fig. GQ8: Receptacle (PC4396-3)
US PLUGS
US Plug Fig. 7P: Plug can be attached to any lead configuration.
     
PDF File Mica Band Catalog Sheet

Band - Mica



Ecommerce Shopping Cart Software by Miva