Store Front Account Search Basket Contents Checkout
Sign In
Order History


Manufacturers
Environmental
   Carbon Dioxide
   Dust Emission Monitors
   Humidity & Dewpoint
   Carbon Monoxide
   Smoke Detection
   Oxygen Measurement
   Barometric Pressure
   Wind and Weather
   Particle Counters
Temperature
Level
Pressure
Flow
Sensors & Transmitters

 

 

 

 

sales@iprocessmart.com
Tel: 1-925-706-7433



Babbitt FT4100 Dust Emission Monitor, Complete Unit
 
Babbitt  FT4100 Dust Emission Monitor, Complete Unit
    Quantity in Basket: None
    Code: BAFT4100-DEM
    Price: $3,350.00
    Shipping Weight: 10.00 pounds
     
     
    Quantity:
     
    Babbitt FT4100 Dust Emission Monitor

    Babbitt FT4100 Dry Material Flow Transmitter

    The FT4100 is designed to sense dust emissions passing through a filter in a dust collector or bag house. This very sensitive device allows the user to continuously monitor the level of emission, and record the data. The FT4100 allows simple, no calibration, "plug and play" monitoring of filter conditions in a baghouse or dust collector. The solid 316SS probe is placed in the discharge duct of the dust collector. Dust particles passing by the probe induce an electrical charge that is carried along the low noise coaxial cable to the control unit. The control unit displays the sensed values, alarms and provides a 4-20mA output proportional to the level of emissions
    For applications that have electrically conductive dusts, condensate or moisture which would cause a build-up on the sensing probe we offer a system with a coated probe that will be unaffected by such conditions; please specify option "PP" when ordering for this option.
    A semi-circular bar graph displays the dust leakage levels on a logarithmic scale (field selectable linear scale is also standard). The bar graph corresponds to a real time digital readout. A flashing "Alarm" and "Pre-Visible" message signals when set points have been exceeded. One segment of the bar graph will hold the peak value reading allowing operators to observe the peak value in a fast changing environment.
    Dust emissions occur at two different times and at two different levels in a dust collector. The first is the baseline emission level, which is the normal leakage whenever the collector is in operation. Typically a higher emission level occurs when the filters are being pulsed or cleaned by reverse air.

    Brochure

    FT4100 drawing

    FT4100 Emission Data Chart Recording FT4100 Flow Transmitter
      The illustration shows how a chart recorder can be used to record emission history and predict bag house or cartridge filter failure.  
    The FT4100 allows the operator to precisely set the alarm setpoint when the baseline leakage increases, when the peak levels during cleaning increase or both! A time delay (0-60 seconds) is user programmable via the keypad to filter out nuisance alarms for both setpoints. One on-board relay is the output for both alarm signals. A 4-20mA signal proportional to the dust leakage is provided for recording or remote monitoring of the dust filters condition.
    Construction
    The FT 4000 comes complete with the electronic circuit board mounted in a NEMA 4X enclosure, 15 feet of low noise coaxial cable and connectors, and a 316 stainless steel probe mounted in an explosion-proof enclosure.
    An optional Shield Screen is available for the probe. The Shield Screen is designed to shield the probe from unwanted electrical noise in the duct that may be caused by nearby fans or motors. It can also shield the probe from stray static electrical charges created in non-metallic ducts. The Shield Screen bleeds the electrical noise to ground, before it reaches the probe, while allowing the dust in the air stream to collide with the sensing probe.
    Specifications  
    Power: 120VAC (+/- 15%) 50/60Hz, 10 watts, standard. 230VAC and 24VDC are optional.
    Analog Output: 4-20mA ouput proportional to display. Non-isolated, 500ohms max.
    Relay Output: 1 Form C contact, SPDT relay, 10Amp resistive at 240VAC; 24VDC.
    Sensor: Passive sensor. No voltage or active components.
    Intrinsic Safety: Intrinsic Safety Barrier is built into the control unit.
    Display: LCD calibrated to unit of charge.
    Time Delay: ON DELAY selectable for 1, 5 or 30 seconds.
    Process Entry: 3/4" NPT standard. 1.5" triclamp quick-connect optional. Probe air purge is available as an option with both connection types.
    Conduit Entry: 3/4" NPT
    Temperature: Probe: -30 deg F to +450 deg F
    Electronics: 10 deg F to 320 deg F
    Note - High temperature ratings are available, contact the factory with your application data.
    Pressure: 85 psi @ 75 deg F.
    Note - High pressure ratings are available, contact the factory with your application data.
    Probe Construction: Probe: 1/2" diameter, 316 stainless steel. 1-1/2", 3", 6" or 12"length standard.
    Insulator: Ultra High Molecular Weight Polyethylene (UHMWP); Teflon optional.
    Housing: Housed in a copper-free cast aluminum explosion-proof enclosure. Class I, Group C, D; Class II, Group E,F,G; Class III.
    Electronics Enclosure: Non-metallic; 6" x 6" x 4" with clear acrylic window; rated NEMA 4X-12-13


    Related Item(s)
    Code Name Image Price  
    BACOAXLN Low Noise Coax Cable   $10.00
    BAFT4100-316P BAFT4100 316SS Probe Adder   $35.00



    Ecommerce Shopping Cart Software by Miva